Número de pieza
Desmilitarización
Vigencia
UOM
NIIN
Desmilitarización:
Yes - DEMIL/MLI
NSN
Número de acciones nacionales:
TXT
Descripción:
Engine Accessory Generator
Código de nombre del artículo:
17311
MRC:
A measurement of the extent of threads,including incomplete threads,along a line parallel to the longitudinal axis.AASA
Thread Length:
0.750 inches
Second Step Diameter:
0.874 inches
MRC:
A measurement taken at right angles to the length of a keyway,in distinction from thickness.ABRR
Keyway Width:
Between 0.249 inches and 0.251 inches
Unthreaded Portion Length:
1.125 inches
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the mounting.ADER
Mounting Style:
Bracket mtd w/three mtg holes top hole threaded
MRC:
The environmental elements or conditions that an item is designed or protected to resist or withstand satisfactorily.ADZC
Environmental Protection:
Corrosion resistant
MRC:
A measurement of the longest dimension of a keyway,in distinction from width.AFYS
Keyway Length:
Between 0.308 inches and 0.313 inches
MRC:
An indication of whether or not an item is capable of operation while submerged.AHZV
Submersibility:
Submersible
MRC:
The direction of rotation of a rotating shaft as viewed from the drive end.AKCT
Shaft Rotation Direction:
Counterclockwise
MRC:
The distance from the end of the item to the center of the keyway.ANTX
Distance From End To Keyway Center:
1.375 inches
MRC:
The minimum speed the armature can revolve and maintain full current output,expressed in revolutions per minute.BCGD
Armature Minimum Speed In Rpm At Full Current Output:
2000
MRC:
The maximum amount of output current for which the item is rated,expressed in amperes.BCGF
Maximum Output Current Rating In Amps:
100.0
MRC:
The cut-in speed necessary to maintain a minimum current flow,expressed in revolutions per minute.BCGG
Minimum Current Cut-in Speed In Rpm:
750
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the shaft drive end.BCGS
Shaft Drive End Style:
Straight shaft end threaded w/keyway
Distance Between Shaft Center And Bottom Mounting Hole Center:
4.125 inches
Distance Between Shaft Center And Top Mounting Hole Center:
4.025 inches
Angular Deviation Of First Hole From Top Center In Deg:
201.0
Angular Deviation Of Second Hole From First Hole In Deg:
159.0
Distance Between Inside Surfaces Of Hinge Bracket:
7.250 inches
Distance Between Outside Surfaces Of Hinge Bracket:
8.118 inches
Bottom Mounting Hole Diameter:
0.453 inches
MRC:
The speed the armature can revolve and produce maximum current,expressed in revolutions per minute.BCND
Maximum Rated Armature Speed In Rpm:
8000
MRC:
A designation indicating the diameter-pitch combination and the number of threads per measurement scale applied to a series of diameters.BZRR
Thread Series:
Unf
MRC:
A designation distinguishing one group of thread diameter-pitch combinations from another by the number of threads per measurement scale for the specific diameter of a threaded mounting hole.CMLK
Mounting Hole Thread Series Designator:
Unc
MRC:
The length of a straight line which passes through the center of a threaded mounting hole,and terminates at the circumference.CMLL
Mounting Hole Thread Diameter:
0.375 inches
MRC:
The number of mounting hole threads per linear inch measured on a line parallel to the thread axis.CMLM
Mounting Hole Thready Qty Per Inch (tpi):
16
MRC:
The number of threads on the item per linear inch measured on a line parallel to the thread axis.CMLP
Thready Qty Per Inch (tpi):
16
MRC:
The total electrical voltage.ELEC
Voltage In Volts:
28.0
